Сильное дымообразование

[Rus_Tiger]

Пытаюсь смоделировать объект, когда запускаю - начинается сильное дымообразование!!! во всех комнатах одновременно... Не могу понять в чем дело... Хотя задан только небольшой участок...

Вот код:

&HEAD CHID='Vicktor'/
&TIME T_END=600.00/
&DUMP RENDER_FILE='Vicktor.ge1', DT_DEVC=1.00, DT_ISOF=1.00, DT_PL3D=1.00, PLOT3D_QUANTITY='DENSITY','DENSITY','DENSITY','VISIBILITY','TEMPERATURE', PLOT3D_SPEC_ID(1:3)='carbon dioxide','carbon monoxide','oxygen'/
&MISC SURF_DEFAULT='SURF', CO_PRODUCTION=.TRUE./

&MESH ID='SETKA1', IJK=40,40,20, XB=0.00,6.00,0.00,6.00,0.00,3.00/
&MESH ID='SETKA2', IJK=40,25,20, XB=6.00,12.00,0.4500,4.20,0.00,3.00/
&MESH ID='SETKA3', IJK=30,44,20, XB=12.00,16.50,0.4500,7.05,0.00,3.00/

&REAC ID='REAC',
C=2.50,
H=9.20,
O=3.00,
N=0.00,
X_O2_LL=0.00,
HEAT_OF_COMBUSTION=1.4500000E004,
CO_YIELD=3.0000000E-003,
SOOT_YIELD=6.0000000E-003,
VISIBILITY_FACTOR=5.50/

&SURF ID='SURF',
COLOR='RED',
HRRPUA=148.00/

&DEVC ID='Datchik_CO', QUANTITY='DENSITY', SPEC_ID='carbon monoxide', XYZ=14.00,3.25,1.70/
&DEVC ID='Datchik_CO2', QUANTITY='DENSITY', SPEC_ID='carbon dioxide', XYZ=14.00,3.25,1.70/
&DEVC ID='Datchik_HCL', QUANTITY='DENSITY', SPEC_ID='other', XYZ=14.00,3.25,1.70/
&DEVC ID='Datchik_O2', QUANTITY='DENSITY', SPEC_ID='oxygen', XYZ=14.00,3.25,1.70/
&DEVC ID='Datchik_TEMP', QUANTITY='TEMPERATURE', XYZ=14.00,3.25,1.70/
&DEVC ID='Datchik_TEPLO', QUANTITY='RADIATIVE HEAT FLUX GAS', XYZ=14.00,3.25,1.70/
&DEVC ID='Datchik_VID', QUANTITY='VISIBILITY', XYZ=14.00,3.25,1.70/
&OBST XB=0.00,6.00,0.00,0.4000,0.00,3.00, SURF_ID='INERT'/ Bottom Wall (Min X)
&OBST XB=5.60,6.00,0.4000,5.40,0.00,3.00, SURF_ID='INERT'/ Right Wall (Max Y)
&OBST XB=0.00,6.00,5.40,5.80,0.00,3.00, SURF_ID='INERT'/ Top Wall (Max X)
&OBST XB=0.00,0.4000,0.4000,5.40,0.00,3.00, SURF_ID='INERT'/ Left Wall (Min Y)
&OBST XB=6.00,12.00,0.50,0.90,0.00,3.00, SURF_ID='INERT'/ Wall
&OBST XB=6.00,12.00,3.50,3.90,0.00,3.00, SURF_ID='INERT'/ Wall
&OBST XB=12.00,12.40,0.50,7.00,0.00,3.00, SURF_ID='INERT'/ Wall
&OBST XB=16.00,16.40,0.50,7.00,0.00,3.00, SURF_ID='INERT'/ Wall
&OBST XB=12.40,16.00,6.60,7.00,0.00,3.00, SURF_ID='INERT'/ Wall
&OBST XB=12.40,16.00,0.50,0.90,0.00,3.00, SURF_ID='INERT'/ Wall

&HOLE XB=5.3000000E000,6.3000000E000,1.5000000E000,2.5000000E000,0.0000000E000,2.0000000E000/ Wall Hole
&HOLE XB=1.1600000E001,1.2600000E001,1.5000000E000,2.5000000E000,0.0000000E000,2.0000000E000/ Wall Hole[1]

&VENT SURF_ID='SURF', XB=2.00,3.00,3.00,4.00,0.00,0.00, XYZ=2.50,3.50,0.00, SPREAD_RATE=0.0103/ Ochag pojara

&ISOF QUANTITY='DENSITY', SPEC_ID='carbon dioxide', VALUE=0.1100/
&ISOF QUANTITY='DENSITY', SPEC_ID='carbon monoxide', VALUE=1.1600000E-003/
&ISOF QUANTITY='DENSITY', SPEC_ID='oxygen', VALUE=0.2260/
&ISOF QUANTITY='VISIBILITY', VALUE=0.1190/
&ISOF QUANTITY='TEMPERATURE', VALUE=70.00/

&SLCF QUANTITY='DENSITY', SPEC_ID='carbon dioxide', PBZ=1.70/
&SLCF QUANTITY='DENSITY', SPEC_ID='carbon monoxide', PBZ=1.70/
&SLCF QUANTITY='DENSITY', SPEC_ID='other', PBZ=1.70/
&SLCF QUANTITY='DENSITY', SPEC_ID='oxygen', PBZ=1.70/
&SLCF QUANTITY='VISIBILITY', PBZ=1.70/
&SLCF QUANTITY='TEMPERATURE', PBZ=1.70/


&TAIL /

Кто может подсказать в чем проблема?

[Nadezhda]

&MISC SURF_DEFAULT='SURF', CO_PRODUCTION=.TRUE./

&SURF ID='SURF',
COLOR='RED',
HRRPUA=148.00/

У вас на всех поверхностях по умолчанию задана горелка.

[Rus_Tiger]

Спасибо!